Rail & Fittings

AREMA 115RE vs 136RE Rail Specification & Selection Guide

AREMA flat-bottom rails 115RE and 136RE are two widely used rail profiles in North America, Latin America, Africa and global mining & port railway projects. They follow AREMA Chapter 4 and ASTM A1 requirements, and are frequently specified in tender documents for freight lines, industrial sidings, mine haulage and container yard tracks.

Many buyers, civil contractors and track engineers struggle to decide which profile fits their project. Although both belong to the AREMA RE rail family, they have different geometric profiles, section moduli, load capacity and maintenance economics. 115RE and 136RE are NOT interchangeable. Fishplates, fasteners, base plates and rail pads are profile-specific.

What Do 115RE and 136RE Stand For?

RE = Rail, American flat-bottom rail profile.

  • 115RE: 115 lb/yd nominal weight, approximately 56.9 kg/m
  • 136RE: 136 lb/yd nominal weight, approximately 67.5 kg/m

Important note: Do not confuse AREMA RE rail with European 60E1 (UIC60) or Chinese P60 rail. Different profile geometry, different tolerance systems and incompatible wheel-rail contact.

Core Dimension Comparison

Item AREMA 115RE AREMA 136RE
Nominal weight 115 lb/yd (56.9 kg/m) 136 lb/yd (67.5 kg/m)
Rail height 168.27 mm 185.70 mm
Rail head width 69.85 mm 74.61 mm
Rail base width 139.70 mm (5.5 inch) 152.40 mm (6.0 inch)
Section modulus Lower Higher
Standard length 12 m / 25 m 12 m / 25 m

Steel Grades & Mechanical Properties

AREMA rails are available in three mainstream grades for both profiles: Standard Carbon (900A), Intermediate Strength (1100) and Head Hardened (HH / 1200 /1300). Head-hardened rail is the preferred option for curves, braking zones and high wear locations.

Grade Tensile Strength Hardness Typical Use
900A Standard Carbon ≥983 MPa Min 310 HBW Gen sidings, low-medium traffic
1100 Intermediate ≥1138 MPa 330–360 HBW Mixed passenger & freight
1200 /1300 HH Head Hardened ≥1179 MPa Min 370 HBW Heavy haul, tight curves, mines, ports

Chemical composition (wt%, common for AREMA rail): C: 0.69–0.86%, Mn:0.70–1.25%, Si:0.10–0.60%, P≤0.020%, S≤0.020%

HH rail only receives accelerated cooling on the rail head, not full-section quenching. It delivers excellent wear resistance and rolling contact fatigue (RCF) performance, similar to EN R350HT but under separate AREMA acceptance criteria. AREMA HH cannot be directly substituted for R350HT in EN tenders.

Application & Axle Load Guidance

115RE Rail

  • Suitable axle load: Up to 25–30 t
  • Typical scenarios: Regional freight lines, commuter passenger lines, industrial sidings, medium-volume mine tracks, port internal transfer lines
  • Advantages: Lower initial investment, mature fastener supply, easier handling and transportation
  • Limitation: Not recommended for continuous heavy axle loads or ultra-high tonnage routes; bending fatigue risk rises under long-term heavy haul

136RE Rail

  • Suitable axle load: 30 t and above, Class I heavy haul lines
  • Typical scenarios: High-volume ore & coal haulage, main freight trunk lines, large container terminals, high-tonnage long-term projects
  • Advantages: Larger section modulus, higher stiffness, less deflection, better fatigue resistance, longer service life, lower life-cycle maintenance cost
  • Limitation: Higher material cost, heavier lifting & installation work, dedicated fishplates and fastening system required

Welding & Inspection Requirements

Both 115RE and 136RE support flash butt welding and aluminothermic welding for CWR continuous welded rail.

  • Standard inspection package: UT ultrasonic testing, dimensional check, straightness control, surface visual inspection, hardness sampling and tensile test.
  • Mill Test Certificate (MTC) is mandatory for most international tenders; 3.1 certificate is widely requested.
  • Special reminder: HH head-hardened rail requires qualified welding procedure specification to avoid rail head softening at weld joints.

115RE vs 136RE: Quick Selection Checklist

Choose 115RE if:

  • Axle load ≤30 t
  • Medium traffic, mixed passenger and freight
  • Budget-sensitive siding, branch line or temporary track
  • Replacement project originally built with 115RE fasteners

Choose 136RE if:

  • Axle load >30 t, heavy haul main line
  • High annual gross tonnage, ore/coal mining railway
  • Long-term design life, priority on reducing track maintenance
  • New build Class I freight corridor or large port main track

Conclusion

115RE and 136RE are both trusted AREMA rail solutions, but they serve different load tiers. 115RE balances cost and performance for medium-load tracks, while 136RE is the premium heavy-haul profile for high axle loads and high tonnage. When preparing tender quotations or technical proposals, confirm axle load, annual tonnage, curve radius and existing fastener system before finalizing rail profile and grade. Selecting the correct rail grade (standard carbon or HH head-hardened) is equally critical for long-term track reliability.

lckj

Recent Posts

A Complete Guide to ERW, LSAW, SSAW Steel Pipe: Distinctions and Selection Tips

Introduction Welded carbon steel pipes are the most widely used solution for oil & gas…

2 days ago

3PE Coating Inspection Standard: Holiday Test, Thickness & Peel Test + Batch Destructive Tests per ISO 21809-1

3-layer polyethylene (3PE / 3LPE) external coating remains the dominant corrosion protection system for buried…

5 days ago

A Full Introduction to OCTG Pipes: Drill Pipe, Casing and Tubing

OCTG, short for Oil Country Tubular Goods, is a comprehensive term for specialized steel tubular…

1 week ago

How to Select the Right Anti-Corrosion Coating: 3PE vs 3PP vs FBE for Pipeline Projects

3PE, 3PP and FBE are the dominant external anti-corrosion coatings for buried and subsea oil,…

2 weeks ago

API 5CT Tubing & Casing Testing Guide: Body Inspection and Thread Check

Oil tubing and casing (OCTG) work under extreme downhole conditions: high pressure, high temperature, tension,…

2 weeks ago

Tubing Thread Types: API 5CT NUE, EUE, IJ and Premium Connections Guide

For oil and gas completion design, tubing thread connection is one of the most critical…

2 weeks ago